SINCE 1990 BRANCHES ARE IN DELHI | PUNE | BANGALORE ~ CIOB TRAINING PARTNERSHIP  ​BHADANIS INSTITUTE'S RUNS UNDER BHADANI QUANTITY SURVEYORS AND TRAINING PVT LTD ~ REGISTERED IN DELHI, INDIA CIN NUMBER U74900DL2016PTC290542.~ TRAINED MORE THAN 116000+ PROFESSIONALS WORLDWIDE​

​​​BHADANI’S PLUMBING DESIGN AND DETAILING COURSE FOR ALL ENGINEERS

Plumbing Designing  Duration 45 Days (30 Days + 15 Days Project)​

​1. Plumbing Systems
a. Fundamentals of Plumbing System
b. Introduction, Definitions & Concepts
c. List of codes & Standards
d. Fixtures, Faucets and Fixture fittings
i. Washbasin
ii. Water Closet
iii. Bidet 
iv. Bathtub 
v. Shower 
vi. Urinals
vii. Kitchen sink
viii. Floor Drain

2. Design of Domestic Water Supply and Distribution System
a. Requirements of Water Supply system
b. Water Demand Calculations Water
c. StorageCalculationsUndergroundSump(UGS)sizing
ElevatedstorageReservoir(ESR)sizingInternalWater
Supply System
d. Direct Pumping System
e. Hydro-pneumatic system
f. Over Head tank distribution system
g. Design Procedure for Internal Water Supply System
h. Flow rate (q) & Loading Unit (z)-From probability equation
i. Hazen Williams Formula for Head loss Calculation 
InternalWater Supply Pipe sizing calculations
Pumping Calculations- HP/Watts
j. Number of tapping to be connected Heavier Size Pipes.
k. Material used in internal water supply system
l. . External. Water Supply System
m. Number of Population served
n. Number of Fixtures served by Each Pipe
o. Design Procedure for External Water supply System External 
Water Supply Pipe Sizing Calculations Material used
in External water supply system 
p. Water Supply Schematic Layout

3. Design of Sanitary Drainage System
a. Requirements of Sanitary Drainage System
b. Types of Sanitary Drainage Systems
c. Single stack system
d. Single stack (partially ventilated ) system
e. One Pipe System
f. Two Pipe System
g. System requirement for Internal Sanitary Drainage System
h. Internal Sanitary Drainage Pipe Sizing Calculations
i. Design Procedure for External Sanitary Drainage System
j. External Sanitary Drainage Pipe Sizing Calculations
k. Calculation of Slope by Manning’s formula
l. Calculating Depth of Inspection Chamber/Manholes
m. Sanitary Drainage Schematic Layout 
n. Design of Storm Water Drainage System
o. Design of Basement Drainage System
p. Using Manning’s Formula and Rational formula
q. Storm Water Drainage Pipe Sizing Calculations
r. Material used in Sanitary Drainage system

4. Drawings – Plumbing Layouts
a. Legends used in Plumbing 
b. Legends used in Plumbing 
c. Typical Floor Plan-Plumbing Layout
d. Enlarged Kitchen & Utility-Plumbing Layout
e. Riser Diagram for multi storied buildings.

5. The Other aspects
a. Life Cycle of the Project
b. Different stages in Design and Drafting
c. Communication between the different teams,
d. Mode of communication using standard formats
and templates
e. Project Management Tools
f. Maintaining Safe and healthy working environment

6. Employability Skills Improving
a. Resume Writing Skills Improving 
b. Interview Skills En powering
c. En Powering of Interpersonal Relationships.
d. Stress Management.
e. Positive Attitude Development.
f. Self-Motivation.

BHADANI’S Quantity Surveying in - Billing Engineering

Invoice Engineering
Level 2 Duration :- 25 Days

1. Understanding the Role of BHADANI'S Billing Engineer / Invoice Engineering in the Construction Industry of India and World
   

2. Billing Engineering Tasks at Site Office and Understanding the Role in Head office with the Client Coordiation
   
3. Account Basics requirement for Billing Engineer
   
4. Construction Billing Procedures From Client Side as well as Contractor Side
   
5. Interim Payment Certification (IPC) from Client Sides as well as Contractor Side
   
6. RA Bill Making - Client Billing - Subcontracting
   
7. Billing with GST and Without GST - hands of Expertise
   
8. CPWD and Corporations and PSU's Techniques of Billing 
   
9. Invoice Generation Through ERP 
   
10. Claim and Dispute Settlement Procedures and all required techniques in Billing and MIS Generation for the same
    
11. Material Engineering Bills for Both Client Side as well as Contractor's Side
    
12. ​Third Party Contractor Billing
    
13. Joint Venture Companies / Contractor Billing
    
14. Petty/ Vendor Billing 
    
15. Preliminary Billing - Post Construction Billing
    
16. InterAlia Billing , International Billing Challan Generation
    
17. Claim Management Procedures used by Invoice Engineers
    
18. Claim of Price Variations as per Norms of Govt. of INDIA
19. Claim of Quantity Variations as per the Norms of Govt. of INDIA
20. Mode of Measurement as per IS Codes with Nomenclatures
21. Claim of Extra Item Analysis of All Kinds of Civil Works During the Site Execution as well as Post Contracting Period
    
22. Vendor Vs. Client Bill Reconciliation

QUALITY CONTROL QUALITY ASSURANCE FOR ALL ENGINEERS

Module1

Roles and Responsibilities of QA / QC Engineer – Civil
Module 2

Introduction to ISO 9001 . ISO 9004 , ISO 14000. ISO 19011
Module 3

International Codes and Standards
Module 4

Drawings and Abbreviations
Module 5

Excavation and Backfilling
Module 6

Construction of Asphalt Concrete paving
Module 7

Concreting Works
Module 8

Pre Stressed Concrete – Bridge Girders
Module 9

Concrete Trial Mix Test, Concrete Compressive Strength Test , Compaction (Density) Test etc.
Module 10

​Receiving Inspection , In process Inspection & Final Inspection
Module 11

Control of Nonconforming of Items / Products
Module 12

Calibration of Monitoring & Measuring Equipment
Module 13

Project Quality Plan
Module 14

Preparation of Inspection Test Plans – ITPs
Module 15

Preparation of QC Procedures

electrical design and drafting for electrical engineers and construction professionals

​1. General
2. Codes & Standards to be followed 
• Indian electricity rules
• National electrical code of India (NEC)
• National building code of India (NBC)
• Applicable standards issued by Bureau of Indian standards (BIS)
• Institute of Electrical & Electronics Engineers (IEEE)
• Regulations of local fire authorities
• Requirements stipulated by Pollution control Board for Noise & Air 
3. Electrical equipment’s and its application used in the installation
• Control devices
• Measuring devices
• Circuit protection devices
• Transformers
• Diesel generators
• Capacitors
• Bus ducts, Bus-bars, Cables (HT/LT) & wires
• Motors & Pumps
• Luminaries – General & Emergency
• Isolators & socket outlets
• UPS/Inverter & Battery banks
• Earthing or Grounding
• Lightning arrestor
4. Means of electrical distribution for installation
• Panels (LT)/Switch Board/Motor control centers (MCC’s)/Final Distribution boards (DB’s)
• Cable trays, trunking or raceways, conduits & underground Pipes (Concrete/PVC)
5. Major electrical loads used in the installation
• Lighting load – Internal & external
• Utility power load
• HVAC loads like FCU’s, Fans etc
• PHE & FF loads like Water transfer pumps, Booster pumps, Fire Fighting pumps, Jockey pumps etc
• Lifts (Elevator) load
• Computer & data centre (Server) loads for office building
6. Electrical design calculations
• Load & maximum demand calculation
• Transformer sizing calculation
• DG sizing calculation
• Short circuit calculation
• Voltage drop calculation
• Capacitor sizing calculation
• Cable sizing calculation
• Earthing calculation
• Lightning calculation
• UPS/Inverter sizing calculation
• Battery sizing calculation 
7. Various design stages & Sequence of electrical design procedure 
Concept design stage
• Understanding the building plans, elevations & sections
• Gathering specific data from the utilities(Electricity board)
• Understanding clients specific requirements
• Preparation of basis of design which should include the cost estimate.
Schematic design stage
• Preparation of Load calculation to arrive maximum peak demand
• Sizing of all Equipments, cables, cable trays
• Electrical design calculations
• Preparation of single line schematic of electrical distribution system with metering options
• Preparation of lighting, small power, earthing & miscellaneous layouts
• Preparation of technical specification
Detailed design stage
• Preparation of detail layouts including sectional details wherever required
• Coordination with other services like HVAC,PHE & FF layouts
• Preparation of bill of quantities(BOQ)
• Preparation of shop drawings based on the tender drawings issued by 
Electrical consultants for installation.
• As built drawings shall be prepared and handed over to client’s representative

Eligibility
Any Graduation, Diploma

BHADANI’S  quantity surveying in tendering & construction contract management

( national and international contracting and competitive bidding)
Level 3 & 4:-​​​ Duration :- 30 Days

1. Tendering Documents Preparation
   

2. Tendering Documents Submission Guidelines

3. Tender Review Reports Generation (T.R.R) for the Contractors as well as Consultants
   
4. Technical Bidding As per Government Laws and as per BHADANI'S Technique
   
5. Financial Bidding As per Government Laws and as per BHADANI'S Technique
   
6. ​Statutory Documents Preparation Techniques for the Tender 
   
7. Purchasing and Negotiation Techniques used by Clients and as well as Contractor's Side
   
8. Pre-Bid Meeting Strategy Building and Coordination with Client 
   
9. Finding Deviations and Clarify with the Client
10. Tender Hunting 
    
11. Reverse Auctioning Strategy Building and Pressurizing client for the tender
    
12. Pooling Technique to use effectively for the Tender to get Maximize Benefits
    
13. Evaluation Strategy - Bidding Strategy - Relationship Building 
    
14. Indemnify the Tender with the Use of Effective Monitoring of the Tender
    
15. Entering Into Contracts - Strategy Building Approach - Scientific Approach
    
16. Construction Contracts Documents Formulation and Preparation
    
17. Procedures in Contract Management - Pre - Construction and Post Construction Phase
    
18. Clearing , Forwarding and Transport 
    
19. Transport Management
    
20. Interpretation of Contracts and Contract Terms
    
21. Cost Overrun and Time Overrun - Strategy Building Approach
    
22. Indian Laws for Construction Contract Management
    
23. FIDIC International Laws (EPC Turnkey Projects)
    
24. Work Order Preparation ( Like Alstom Siemens Etc.)
    
25. Live Project Training for Procurement and Negotiation Techniques
    ​​
    

CIVIL, MECHANICAL AND ELECTRICAL  ENGINEERS AFTER DOING LEVEL 1 TO LEVEL 5 ~BECOME BUILDER, CONTRACTOR, CONSULTANT, ESTIMATOR, QUANTITY SURVEYOR, COST ENGINEER, BILLING ENGINEER, PLANNING ENGINEER, TENDERING ENGINEER, CONRACT MANAGER , CONSRUCTION PROJECT MANAGER QUALITY ENGINEER

​BHADANI’S Quantity Surveying in  Construction Project Planning & Management (CPM)
Level 5 Duration :- 25 Days

1. Critical Thinking and Problem Solving Approach 

2. Strategical Thinking and Risk Analysis 
3. Project Planning - Master Plan Generation 
4. Project Management Procedures Used for Construction Industry by Big MNC's and Construction Companies of India and World
5. Role of Project Manager in Construction Industry
6. Project Budget Preparation with all factors analysis in Hand
7. Actual Situation Comparison with Budget Amount
8. Progress Monitoring with the Key Indicators Strategy
9. MS Project Basics - Scheduling 
10. Project Coordination Techniques with Accounts , HR , Purchase and Procurement Departments with easy solutions 
11. Management Information Generation
12. Modern Building Construction Trends Execution Plan & Strategy Building
13. Resettlement and Rehabilitation (R&R) for speedy progress of work
14. Quality Assurance with Total Quality Control Planning 
15. Site (Field) Management Techniques used by Project Managers at Site
16. Management of Emergencies in High Rise Buildings
17. Self Inspection for Quality Construction at Site
18. Cost and Time Controlling Strategies used for Construction Projects
19. Cash Flow Monitoring - Budget Vs Actual Comparison
20. Green Sheet Report - Profit and Loss Determination for Construction Projects
21. SWOT Analysis for Construction Project
22. JIT Implementation in any Construction Project
    
23. ​Earned Value Management (EVM) in Construction Project
    

BHADANI’S Quantity Surveying in Estimation Civil - Construction
Level 1 - Duration :- 45 Days

1. Understanding the Role of BHADANI'S Quantity Surveying in the Construction Industry

2. Checklist of All Kinds of Civil Works at Site.

3. Construction Methodologies of Civil Works and How it works in Construction Industry
4. Construction Activities Identification Analysis and Report Generation
   
5. Making Project Chartered and Feasible Reports
   
6. Project Risk Analysis and Action Reports
7. Understanding and Reading the Structural and Architectural Drawings
   
8. Quantity Take off From the Drawings Like PCC , RCC , Reinforcement , Shuttering Etc.
   
9. Quantity Take off From the Architectural Drawings (Like Brickwork, Plaster Painting Putty Work Etc.)
   
10. Faster Take off Methodologies from Drawings of Civil
    
11. Analysis of All Kinds of Civil Drawings with Proper Presentation in Excel Formats
    
12. Management Information System (MIS) Generation and Preparation in Proper Formats as per IS Standards
    
13. Estimation of All Kinds of Civil Works 
    
14. Estimation Technique  During Design Phase 
    
15. Estimation Technique During Pre-Construction Phase
    
16. Estimation Technique During Post-Construction Phase
    
17. Calculator Making of Concrete Steel, Brickwork, Plaster Painting Etc.
    
18. Pre-Engineered Building (PEB) Estimation 
    
19. Costing Techniques of All Kinds of Civil Works (Concrete , Brikcwork, Earthwork, Finishing Work, Wood Work, Steel Work, Demolishing Works Etc.)
20. Costing Techniques- Risk Based Costing
    
21. Costing Techniques - Parametric Costing
    
22. Costing Techniques - Machinery Transport Management and Costing
    
23. ​Costing Techniques - Scope Estimation and Cost Analysis
    
24. ​S-Curve Reporting 
    
25. Labour Deployment Planning As per Budget 
    
26. Labour Economics and Productivity Analysis
27. Labour Output Analysis as per IS Code, Schedule of Rates and As per BHADANI'S New Technique
    
28. Economic Order Quantity (EOQ) and Management​
29. Machinery Output Analysis as per Market Standards
    
30. Profit and Loss Analysis in Labour and Machinery Deployed at Construction Site
31. Daily Work Report (DWR) Preparation as per Quantity Surveyor Standards
    
32. Bar Bending Schedule (BBS) of All RCC Structures Like Footing Beams Slabs, Columns , Raft , Footing, Staircase Etc.
33. ​Bill of Quantity (BOQ) Take off (Material and Preparation)
    
34. Rate Analysis of All Kinds of Civil Works
    
35. Material Reconciliation Techniques from Contractor and Client's Side
    
36. Material Procurement Strategies as per the techniques used in Quantity Surveying
    
37. FREE  LANCE Quantity Surveying with Hands on Practice